20 Most Recent
2007 Jeep Wrangler 3.8 Questions & Answers
Wont shift out of first
so is an automatic, unlike my 6speed? m/t-?
ok the a/T
check all fuses yet?
check A/T fluid levels per manual, dont guess, dont overfill it.?
is the fluid pink red, or brown or black?
did you connect a scan tool to see if there are DTC errors from trans,?
that be first, did you, if not ?, its all gue$$ work.
2/22/2015 2:10:42 PM •
2007 Jeep...
•
Answered
on Feb 22, 2015
Recall on jeep
Go to Chrysler web site and search for recalls for you jeep.
7/23/2014 2:52:14 PM •
2007 Jeep...
•
Answered
on Jul 23, 2014
Rear defroster 2007 wrangler switch (button) lights but does not stay on. Checked fuses under hood and connection at rear window. Wiper and fluid work.
this is easy, the fsm covers it, but you dont need it.
you grab any volt meter.
connect it to the grid, (20vdc range) and it read 12vdc on.
if it does the grid is bad
if not relay is bad ,the fuses, or the switch that turns on the relay is bad
all can be found easy with the $10 walfart voltmeter. VOM, or DMM)
do the one test, and post back, can peep the onion as deep as you want ,step by step. if want.
1/22/2014 8:14:40 PM •
2007 Jeep...
•
Answered
on Jan 22, 2014
Ticking noises / Spun Bearing
If it is a light ticking noise it could be something as simple as tappits on rocker arms. valves pinging..........IF it is a ticking and not a KNOCKING noise then i would have another mechanic take a look at it...Sad thing that happens is some mechanics will give wrong suggestion for the simple fact of making your wallet lighter.... not saying this is the caes but something this costly needs more than one mechanics opinion. My suggestion would be have another mechanic look at it not telling what the first mechanics opinion was and then see how they compare..... hope this info helps and good luck....Please rate my post.
8/17/2012 8:43:23 PM •
2007 Jeep...
•
Answered
on Aug 17, 2012
Dashboard gauge needles irratic jumping on / off / fluctuating
Found out that irratic dashboard gauge needles jumping all over the place was due to computer harness connector pins getting a little corrosive / rusty.....
cured problem, over several times / applications by disconnecting harness, and spraying W\D 40 on pins (plugging in and unplugging several times), then wiping off pins and corrosiveness, and giving final light coat of W'D 40 and plugging in harness. Took a couple of times before problem disappeared over time.
2002 Jeep wrangler x. Hi my turn signals don't work.
nothing on dash means the whole IP cluster is dead.? (fuses)_
Fuses are first, repeat 3 times for effect.
front and rear turns dead or?
tell what does work all and does not,
telling just one thing bad, is not really usefull.
for sure power feed wise.
head lamps work and park?????? keyoff and on work.
horn works
brake lamps dead?
engine runs good.
I just sold my 2002 wrangler the last good real jeep it was, my bad selling it.
i have all jeep service manuals so easy to answer this 88 to 2010
on most cares I fix dead headlamps first it is hardwired to work at an any time and super simple if not DRL JUNK .
02 TJ jeeps (pure love)./
chapter 8w-52 'turns 'blinks, hazard]s
fuse 7 and 13 not blown
combo flasher not dead. 5 wires. and one pin is IGN, oops.
ign is fuse 13,oops, is it blown/
Hazards dead is same fuse and same InG fuse good.
IGN power comes form KEY switch page 8w-11
IGN switch wire BK-DG , 12vdc key on. if not fuse14 blown 20ams
and goes to the battery direct.
all fuses in the PDC must good, and now dead batteries
or its 4 cable logs ends, loose or rusty.
end.
fuse 10 and and F24 kills the cluster. and f15
fuse is 10 head lamps too and a CB breaker.
fuse 7 dead kills park /neutral switch ,
Not finding what you are looking for?