2009 Chevrolet Malibu LTZ - Answered Questions & Fixed issues

https://www.youtube.com/watch?v=4DB5Cn5mDhY Locate the fuel rail on the intake manifold and on the drivers side follow it back until you see the hose that connects to if. That is the feed hose from the tank.

does it come when you steer, sometimes its the strut bearing that cause this, my car does this when its cold goes away when warm

try changing your fuel filter or fuel pump i would start with the fuel filter first and do process elimination

Check for a blowin fuse, Defective relay, Loose wires break in one of the wires, Switch could be shot, OR evan the motor has burn,t out,

Are you an electronics engineer. Do you have all the test equipment. Can you read wiring schematics. If the answer to any of the above is 'No', you will have a hard time. You can check the 'Balance' knob setting first as you may have all the sound directed to one side. Check the wiring connector on the back, but that is about it. ..

I realize what I say is going to be 5 years old but the dealer has to view your title and vin so they can cut a key.

There are two rods, one has rubber on it. I just replaced the one with rubber on it. Looking at the one rod that was still in place, you can see it mirrors the rod you are going to replace, the placement is just opposite the one that is in there. The rod has a left end that is a square "C" shape, and the right end has a "V" bend right before the end. First position the rod above the seat release cables (if you have them) then position the "V" end near the inside right top of the trunk. Then slide the left "C" end into one of the three slots (I used the bottom slot). Leave it loose so it can rotate with just the tip in the slot. Slide the rod to the right so the "V" is above the spring clip (don't clip it in yet). The right side and the left side of the "V" has to fit into the tabs underneath and inside the top of the trunk. Compare to the left side to see how it fits. Once in place, you can then lower the "V" down to the clip and snap it over the bottom tip of the "V". These steps are easier if the trunk is propped not fully open. I had someone lower the trunk part way while I lay on my back inside the trunk, and I used a small open end wrench to bend the rod slightly to get it to fit into the tabs. The final step is to position the left side of the rod so the torque will hold the lid open. I used a small open end wrench, placed it over the tip in the slot and rotated CW upward until straight part of the rod slid over the hook to hold it in place. This last step had me concerned that I could bend or break the rod, but I went slowly and carefully and was quite happy when it snapped into place and held the lid open.

My 15 amp fuse keep blowing soon I tried to start my car I replaced my fuel pump in my ecm replaced what do y'all think it is

You need to partially drain the cooling system. THe thermostat housing is located on the driver side of the engine block above the transmission bell-housing. Just follow the big radiator hose on the driver side and it will lead you to the housing.THere are the radiator hose,two heater hoses, and another hose leading to the surge tank that you will need to remove from the housing. 3 bolts secure the housing to the block- remove these bolts and remove the housing. You can now remove and replace the thermostat and install a new gasket- i would recommend coating the gasket in SIL-Glyde or Vaseline. Torque the bolts to 89inlb, re connect the hoses. Refill cooling system with antifreeze and burp all the air out.

https://www.autogenius.info/chevrolet-malibu-2004-2007-fuse-box-diagram/

Question edited for full 'year make model'. Question moved to sub category. In the link. Also check the images tab for a Pinterest diagram. https://www.google.com/search?q=2014+chevy+malibu+ltz+radio+wiring+diagram& ..

fluid =filter=flush=pan gasket =tools https://www.youtube.com/watch?v=vajiQGrOzw8

First get your braking system checked by a qualified mechanic! The light comes on because the electronics have detected an issue. You might also need to get the vehicle plugged into a diagnostic system or an obd2 scanner to get the Diagnostic Trouble Codes, (DTC's). Get prices at 3 or 4 different garages as prices for diagnostics can be VERY different! Once repairs are done some dash warning light will turn off automatically.

Not sure unless the 2013 model year was released 9 month's before your question was posted?

What year is your car ?

There usually always on the back of the engine for these models.

Here is a video https://www.youtube.com/watch?v=9rL0Toaeb6o ..

Difficult to see because they are on their side, and Fixya doesn't provide a way to enlarge images. There are some good diagrams here and the video tab has tear down videos https://www.google.com/search?q=1999+3100+sfi+v6+malibu+engine+parts ..

Most likely the front

If the seat is not moving forward or backward, but you do hear a click or a motorsound- chances are that you dropped in some change or other debris may be blockling the way. You might also have blown a fuse - look for fuse no. 30, which is a 30 Amp fuse. Once you've checked all that and if the motor still does not run, then the problem may be with your wiring. Wire colors between the switch panel and motor are: • Fore/aft-Tan and Lt Green • Front up/down-Dark Green and Dark Blue • Rear up/down-Yellow and Light Blue • Recline up/down motor's Blue and Light Green