20 Most Recent
2007 GMC Envoy Questions & Answers
Why doesn't rear axle come out after removing the c clips?
remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.
Remove the brake caliper. Refer to Rear Brake Caliper Replacement.
Remove the rear wheel speed sensor. Refer to Rear Wheel Speed Sensor Replacement.
Remove the rear axle housing cover and the gasket. Refer to Rear Axle Housing Cover and Gasket Replacement (8.0/8.6 Inch Axle) ' Rear Axle Housing Cover and Gasket Replacement (9.5 Inch Axle).
Remove the pinion shaft locking bolt
On axles without a locking differential, remove the pinion shaft.
(learn what locker means and does) or read the RPO list on car.
On axles with a locking differential, remove the shaft part way. Rotate the case until the pinion shaft touches the housing.
- On axles with a locking differential, use a screwdriver, or a similar tool, in order to enter the differential case and rotate the C-lock?(1) until the C-lock aligns with the thrust block?(2).
- Push the flange of the axle shaft?(1) toward the differential.
remove the C-lock from the button end of the axle shaft.
read the manual first.
if he bearing is seized up and they can swell up and be tight
the slide hammer is the only cure here. and is always best to use.
(after all pre steps on 3 different axle types) not told by you.
1 get the RPO first from GM
2; then read the manual.
3: then act.
easy as 1,2,3 ,not guessing and doing damage.
2007 GMC Envoy WILL START, starter will not disengage. New ignition switch, will not disengage. Why?
Question edited for funky spelling and punctuation.
Question moved to model category.
Jeff provides a great answer to the issue
- Jeff Armer Jan 02, 2023. Starter relay contacts stuck closed could be a reason .
-
Circuit Description
Moving the ignition switch to the START position sends a 12 volt signal to the engine control module (ECM)/powertrain control module (PCM) Crank Request circuit. The ECM/PCM verifies that the transmission is in the PARK or NEUTRAL position. With the transmission in Park, voltage flows through the Park/Neutral position switch and feeds the starter relay coil. The ECM/PCM then grounds the control circuit of the starter relay. When the starter relay is energized it allows battery positive voltage to the starter solenoid S terminal. On some vehicles the starter will continue to crank the engine with the key released until it starts or the crank command has timed out to prevent excessive heat build up in the starter circuitry or the ECM/PCM receives an engine run flag.
Where is my vent solenoid and my purdge solenoids located
Vent solenoids there are 2 one on the intake manifold and one on top of the gas tank usually on top of the fuel pump module, the purge solenoid is located on or near the charcoal canister which is underneath the vehicle mounted by the gas tank
How can I replace passenger side fender?
Too many unknowns here. How bad is the fender damaged? Is there any damage to other parts of the body that the fender attaches to? If so, then let a body shop do it because they have the equipment necessary to straighten those body parts. If you still want to give it a go, then take out all the bolts and other fasteners that attach other things to the fender like hose clamps,plastic reservoirs etc. The inner fender well has bolts that have to be removed from the fender. The fender itself has bolts accessible from under the hood. Get them all out and any stiffener rods at the front of the fender. There are a couple of bolts on the bottom of the fender where it meets the body nearest the front door. You have to get those from underneath. Keep track of where all the bolts and fasteners go so reassembly will go smoothly.
I have a 2007 GMC Envoy, the engine light has been on for a while now, took it to the dealer and a code P0506, they reset the light, took my $100 and said nothing is wrong, three days later, the engi
Hi there, P0506 IS usally a dirty throttle body. In order to clean properly, with the battery disconnected, they need to be taken off and cleaned front and back til' they are shiny. Sticking a rag soaked with solvent in there while it's still attached isn't going to cut it, i've seen many mechanics do it this way. When they do this, they very often DO NOT unhook the battery which you NEED to do for about an hour while cleaning.. Otherwise, the computer won't relearn the clean throttle body, and you'll have your light on again. It's very easy and cheap to do it yourself. Let me know if you'd like instructions on how to do it.
Ball joint bolt fell out upper in 2007 GMC Envoy
Upper ball joint? That's not related to the job of replacing a tie rod or tie rod end. It's also not related to the brake job.
It's an '07 and it had a bolt-in ball joint? That's not factory - it's been replaced before.
Not finding what you are looking for?