2008 Ford Focus - Page 2 - Answered Questions & Fixed issues
Ford focus stoping at idling every time what problem
Restricted air flow. Replace the air filter if dirty. Clean the throttle body and MAF sensor. I use brake clean. Use a tooth brush on the throttle body , just spray down the MAF sensor. Leave the MAF off, start the car and spray some in the throttle as you rev it up. If the engine light comes on, it is because of the MAF being off. It will go out in a day or two. Or you can have it cleared.
11/28/2015 4:02:28 PM •
2008 Ford Focus
•
Answered
on Nov 28, 2015
•
127 views
Number 28 fuse keeps blowing
Some wire has lost its cover-layer of insulation, and the bare wire is contacting the metal frame of the vehicle. Kapow!
Get a technician to look for this "short-circuit".
8/21/2015 4:21:20 AM •
2008 Ford Focus
•
Answered
on Aug 21, 2015
•
264 views
Fuse for turn signal
The fuse for the signal lights controls both lights. If the fuse is blown none of the signal lights will work. If the left front/rear signal is not working or is flashing fast suspect a defective bulb
7/10/2015 12:36:20 PM •
2008 Ford Focus
•
Answered
on Jul 10, 2015
•
455 views
Ford Focus air con not working
Unfortunately air con units are pressurised with a volatile gas which over time "leaks" out and eventually stops cooling any air .you will need to have it re gassed or repressurised...ballpark figure is about £75 to have done but you may find someone who can do this cheaper.system need re gassing every so often.
7/2/2015 8:26:11 PM •
2008 Ford Focus
•
Answered
on Jul 02, 2015
•
149 views
What tools do I need to change brake pads on ford focus 2008
A few of these poster are making assumption's on what model 2008 Focus the question is directed. Actually on a Ford Focus S with a 2.0 liter the caliper is held on by 2 metric bolts.
I believe the caliper housing is held on by a 15 mm bolt, and you might need a 17mm to hold the caliper pins from spinning.
A 2008 Focus has no removable spring, just a spring plate that the brake pad rides in.
Remember to loosen the bleeder line with a 10mm when you compress the caliper to get rid of the excess fluid or take off the cap to the master cylinder, so the pressure will not damage the master cylinder. Make sure and clean the caliper slides with brake cleaner and lubricate them with a good non-petroleum base grease.
6/17/2015 1:52:34 AM •
2008 Ford Focus
•
Answered
on Jun 17, 2015
•
2,102 views
The wrench light is on on my 2008 ford focus what
I assume you have no owners manual or never read it.
The wrench is a MIL Lamp--- a Malfunction Indicator Lamp
It tells you that something like a sensor or other issues,is out of range,as far as the PCM (Computer) sees it. When ever you get a check light,mil light,trac,abs ,etc,you go to a repair shop fairly soon,like a couple of days or so, and have the issues checked out. This will happen a couple times a year ,on most of todays vehicles,so get used to it,and expect to pay a diagnostic fee, plus repair
3/26/2015 2:22:15 PM •
2008 Ford Focus
•
Answered
on Mar 26, 2015
•
6,312 views
How do i unlock my radio code on a focus 2008
The code and instructions will be in the radio manual . should be in the glove box with the drivers manual. If lost ford will be able to find it. As each radio has it own code . If going to Ford take proof of ownership and vin number and date.
2/25/2015 8:53:23 PM •
2008 Ford Focus
•
Answered
on Feb 25, 2015
•
309 views
Not finding what you are looking for?