Acura Cars & Trucks - Recent Questions, Troubleshooting & Support


Hi there's this website called reliable-store.com and it is very amazing for manual for repairing servicing anything
someone on fixya recommended it to me and I thank him even today
They have full manuals and it's verrrrry cheap and mine
I got free in offers
3rd time I bought it, I also had an issue with the file so the girl replaced it in 30 mins
there is one website more but i don't remember its name it was 2 years back bitman something link this
Try these out brother

Acura Cars &... | Answered 2 days ago


You can get guide from many sites.. i know few
error codes/ fault codes, wiring diagrams, schematic diagrams, torque specs, engine info, switches functioning, assemble, disassembly, complete refurbish, repair, installation every single thing is covered
within seconds u can get the access and it's totally illustrative complete.. eg. pls try reliable-store.com

2007 Acura MDX | Answered 3 days ago


You can get guide from many sites.. i know few
error codes/ fault codes, wiring diagrams, schematic diagrams, torque specs, engine info, switches functioning, assemble, disassembly, complete refurbish, repair, installation every single thing is covered
within seconds u can get the access and it's totally illustrative complete.. eg. pls try reliable-store.com

Acura Cars &... | Answered 3 days ago


Looks like you have check most of the basics - but i don't see anything about coil packs. Better check those as well. Not likely that all went out, but likely that one is misbehaving. Should be able to see the voltage toggle with a meter on the input. Also check compression to make sure the combustion chamber is OK

1997 Acura RL | Answered on Nov 09, 2019


The question can you get a new one in. you can always cut the old one up enough to get it out. In the past, I've skipped the factory hose and put in a completely flexilbe one. You can have flexible hydraulic hoses made up at most truck shops. The only thing critical is the end connectors. You might even be able to save the old ones and splice in a hose.

1997 Acura RL | Answered on Nov 09, 2019


Fuel reset buttons are usually under passenger kick-panels on the side. Follow fuel lines from engine back and should be able to spot the location as well.

1997 Acura RL | Answered on Nov 09, 2019


Did you resplice the cut wires with solder and shrink wrap - try that first. Then reset the car by disconnecting battery for 30 minutes and reconnect. You want the ecm to re-boot.

Acura RL Cars &... | Answered on Nov 09, 2019


Smoke can only be caused by something burning. Only candidates are oil and water. It doesn't take much - maybe even small enough that you won't notice loss over many miles. Check compression on all cylinders. You should see something there.

1997 Acura RL | Answered on Nov 09, 2019


misfire in all 4 cyclinders hmmm...... compression tester check compression 125psi is good 100 and lower is bad (head gasket they go bad) if that is good, do fuel filter,, or charge system is bad, or bad ground or bad coil

2003 Acura RSX | Answered on Nov 09, 2019


I had the same error. Delete your phone from your MDX, turn off car. Turn back on. Add your phone back to the MDX.

Acura MDX Cars &... | Answered on Oct 21, 2019


KEEP WORKING IT. WHEN IT DOES COME OUT LUBE THE LOCK AND LIGHTLY SANDPAPER THE KEYS SHARP EDGES

Acura Cars &... | Answered on Oct 19, 2019


sounds like an OBD2 comm failure, mine (i have 10) all show comm loss. but.. can be blown fuses killing OBD2 DLC pin 16 (not 12v)
also, of your car is newer and the scan tool is older, it can fail.
newer scan tools work on all cars here. in usa. all, obd2 1996 and newer. (i build oBD2 gauges and can go endless here... comms...)

no Pxxxx code?
what scanner?, there are many. some are junk.
is this a USA car, when posting nobody knows,
in fact, cars up to 2006 world wide, don't have OBD2 ECUs/PCMs.
not posting where car was 1st sold , is a failure.
if you are in usa, we can access the online FSM and look this up.
we use.
alldata.com
or
mitchels.

lets back up. (a real scan tool not a funky useless code reader)
you, make sure pin 16 is hot.
you plug in scan tool (newer) if car has CAN buss? the tool too must be CAN BUSS CERTIFIED.?
you key on. not started.
you push the scan button, no comm fails, you see TPS throttle angle.
and ECT engine temp and air temp and RPM is 0
all that not started enigne yet, if you cant get there, wrong car, wrong tool.
if the engine runs, the tool must scan, if not pin 16 dead.
or wrong scan tool.

2002 Acura 3.5RL | Answered on Oct 18, 2019


Try a shop vac with the narrow attachment. Like the one that is used to vac behind, under and in-between the cushions on your couch.
Works for me every time! Man, I gotta stop getting into accidents.
Good luck,
Jason

Acura Cars &... | Answered on Oct 14, 2019


Automatic or Standard? Check my tip automatic transmission.

2001 Acura MDX | Answered on Oct 13, 2019

Not finding what you are looking for?
Acura Logo

12,423 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2000 Acura TL
2000 Acura TL

413 Questions

1999 Acura TL
1999 Acura TL

404 Questions

1997 Acura CL
1997 Acura CL

407 Questions

1991 Acura Legend
1991 Acura Legend

282 Questions

Top Acura Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...