Konica Minolta bizhub - Recent Questions, Troubleshooting & Support


1102 is output tray lift motor did it hit something on the way down? 2801 replace the drum and developer

Konica Minolta... | Answered on Mar 03, 2019


Power off the machine. Then remove the toner bottle, be careful the hole might be on the bottom and the toner is going to go everywhere. Then close the toner cover and turn on the machine. Let the machine go through it normal routine. When it asks for toner install the toner bottle correctly. If THE KNUB on the side of the bottle is damage put a new one in. That KNUB is what the toner motor uses to turn the bottle, if it damaged you get a code. If that does not work, you might have a bad motor or the home sensor or actuator for the toner bottle is bad worse case the control board is bad

Konica Minolta... | Answered on Mar 03, 2019


FS-523 Finisher lift motor of the where the copies or prints come out the lift motor is shot!! or its not turning to lift the motor did the tray hit something on the way down or up???

Konica Minolta... | Answered on Mar 03, 2019


replace the drum and developer and run TCR and gradation adj

Konica Minolta... | Answered on Mar 03, 2019


First replace the drum and developer

Konica Minolta... | Answered on Mar 03, 2019


Did the machine state to replace the drum and developing unit are they OEM or third party? Did you run gradation?

Konica Minolta... | Answered on Mar 03, 2019


Go to the control panel under paper select bypass tray set to A4 or 81/2x11 select weight and the go to computer select bypass tray and paper weight

Konica Minolta... | Answered on Mar 03, 2019


Check tray 2 paper draw and see if there is paper behind it.

Konica Minolta... | Answered on Mar 03, 2019


See if you can get addational memory from konicaminolta or clear all memory in service mode

Konica Minolta... | Answered on Mar 03, 2019


Any one of theses:

CCD board (CCDB)
Exposure lamp (L1) My Number #1 does the Bright Light under the big glass come on?
L1 inverter (L1 INVVB)
Scanner motor (M2)
Overall control board (OACB)

Konica Minolta... | Answered on Mar 03, 2019


One of the rarest machines in the Konica Minolta line up!!!!!
A printer without a control panel. the code deal with one control board not talking to another, recommend a tech look at it he might be able to re-flash the firmware the copiers operating system worse case one or both boards are bad. Is the machine on a good surge protector not an Ace hardware 9.99 special? Nothing against Ace. But a thousand dollar machine should be protected with a good minimum 100 dollar surge protector.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Mar 02, 2019


A new belt will have to be installed at which time the fuse in the new belt will be blown to start a new count from 0. Now you can replace the fuse in the old one if you know how.

Konica Minolta... | Answered on Feb 24, 2019


Any one of these:
1. CCD board (CCDB)
2. Exposure lamp (L1)
3. L1 inverter (L1 INVVB)
4. Scanner motor (M2)
5. Overall control board (OACB)
I would go with the 3,1,4,5 (IS $$$$$)

Konica Minolta... | Answered on Feb 24, 2019


Recommend have a tech replace the exit section above the fuser (Hot Part) section

Konica Minolta... | Answered on Feb 24, 2019


Its a maintenance code for consumable due, check with any local service personal

Konica Minolta... | Answered on Feb 22, 2019

Not finding what you are looking for?

-508 questions posted

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6825 Answers

George Mclaughlin

Level 2 Expert

364 Answers

Clive
Clive

Level 3 Expert

4345 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Konica Minolta Office Equipment & Supplies

  • Forum

View Most Popular

  • Konica Minolta Office Equipment & Supplies
Loading...