Refrigerators - Answered Questions & Fixed Issues


Thermistors input temperatures to the control boards. Thermistors may have a 2k Ohms value at 70° F, a service manual or guide, or look up part number for replacing any thermistor out of range.

Kenmore... | Answered 3 hours ago | 14 views


Check the line that goes from the water pipe to the back of the refrig. Someone may have used something they shouldn't have. The lines in the refrig won't break down like that.

LG Refrigerators | Answered 4 hours ago | 19 views


Often it's the gears that become bad. See if you can get a new gear set or call in an appliance repair service to install or at lease check it out.

Refrigerators | Answered 4 hours ago | 16 views


Probably the unit is trying to fill because the on/off bar it down (senses the level of ice in the tray). Lift it up to turn off.

Refrigerators | Answered 4 hours ago | 18 views


CALL A LOCAL REPAIR SERVICE THE DAMPER MOTOR MAY NEED REPLACED

Refrigerators | Answered 14 hours ago | 13 views


To have the model number would be very helpful to give you the correct information.

Kenmore... | Answered 7 hours ago | 59 views


Set it initially to 5, then adjust after 8 hours as needed. If the regular liquids (not alcohol) start to freeze in the fridge section, it's too cold!

Refrigerators | Answered 20 hours ago | 18 views


39E is a bad ice maker as you know. Try to heat up the ice maker with a hair dryer in case ice has jammed the ice maker from rotating properly. If it still doesn't work, the entire ice maker would need to be replaced I'm sorry to say. '

So error 40E means your ice maker fan isn't running properly and 24E means your freezer isn't defrosting properly. Both items are inside the freezer behind the back wall. You'll need to pull everything out of the freezer and remove the entire back wall inside the freezer. Thaw any ice or frost built up you see with a hairdryer. Re-install everything and then on the dispenser press and hold the upper right and upper left buttons to reset the error codes. If everything resets, then great. If it won't reset, then you need to replace your defrost temperature sensor clipped onto the top of the silver coils behind the back panel you removed, and you also need to replace the ice fan motor.

Samsung... | Answered 23 hours ago | 2,333 views


In the freezer compartment there is a panel on the ceiling of the freezer, remove this with a small spatula, it snaps off, there is a dial that controls the airflow on the panel, inside this panel is the defrost control board, it does not use the old time defrost timer, it uses this part, its about $250
Cntrl-Elec Part Number: AP6023580 Made by: Genuine Whirlpool part OUR PRICE $259.12 REGULARLY YOU SAVE $260.53 $1.41

Whirlpool... | Answered 21 hours ago | 26 views


Filter may have been installed backwards

Samsung... | Answered Yesterday | 25 views


With a miniscule leak, it is not easy to detect with liquid type detector, a halogen leak detector may or may not detect it.
What after a leak is detected, it needs to be patched, soldered, but refrigerant would need to be removed first.
You may install a tap on service port, it clamps on the line and no soldering required.
With normal operation, the top 2/3 of the condenser coil is hotter than the bottom 1/3 of the coil.

Refrigerators | Answered Yesterday | 21 views


POSSIBLY NEEDS A NEW AIR DAMPER MOTOR CALL A LOCAL REPAIR SERVICE

Refrigerators | Answered Yesterday | 27 views


MargaritavilleCargo.com Customer Service
1-877-689-2737

Refrigerators | Answered 2 days ago | 15 views


Here is a link to the page in the owners manual depicting the process:
https://www.manualslib.com/manual/722607/Whirlpool-Refrigerator.html?page=22#manual

Which from the keypad touch the options and lock together for 3 seconds, a "1 cup" will display, get a measuring cup and locate the 8 ounce or 1 cup mark, place the empty cup under the water dispenser, press the water dispense paddle to fill the cup to the 8 ounce or 1 cup mark, (if you accidentally overfill, touch the back/ice type button, empty cup, and start process over), when cup is at the 8oz/1 cup mark stop filling and touch the measured fill button. You can pour out the water from the cup and test to see if water dispenser is calibrated now (should be as this works for my whirlpool refrigerator, if not attempt process again)

Whirlpool... | Answered 2 days ago | 1,506 views


https://www.searspartsdirect.com/manual/1fse6xozod-000582/kenmore-10677188791-top-mount-refrigerato

Kenmore... | Answered 2 days ago | 28 views


Brand new ice maker has not made ice yet. It has been 3 days. It pulls water, fun runs close to 10 minutes, goes through the motions of dumping ice in the bucket but there is no ice to be dumped. ..........amazon78.com8GBLH5

Magic Chef... | Answered 3 days ago | 19 views


Defective fan or defective wiring

Refrigerators | Answered 3 days ago | 18 views

Not finding what you are looking for?
Refrigerators Logo

Ask a Question

Usually answered in minutes!

Top Refrigerators Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

Brad Brown

Level 3 Expert

18108 Answers

Are you a Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...