There is no grease but oil used in this tool There is a special consumables kit for to order But BEFORE you made a self service for this machine there could be a rip somewhere in the spindle control first by ringing listen to the sound tap on it it with a piece of metal that the spindle sounds well without also all in and outside parts naturally and off if it does is the sds chisel drill conduction inside the spindle is not round toppen instead of square topped because of faultering on the chisel or drill in short time to expect. in that case if the spindle is bad its better to remplacement the whole tool by Bosch for the working hours on all parts are reached, but if the spindle is smooth order 1 615 437 511 oil reservoir and 1 617 000 A16 thats the right maintenance partsset for this machine and its is easy to service by yourself a little 2 or 3 hours without special tools for special kevlar rings like some other brands often have. but a bank vice and some little screwdrivers noseplier, shaft retaining ring pliers a solvent cleaner for the old lubrication to remove.
AND IMPORTANT dont forget part 104 best to give that o-ring some grease that it will not move out by insert the spindle (sometimes)
one thing is very important there must inside be 2 adjust rings between the gears 47 and 51 if there is only one shimring = used then order some shim rings ( there must be made an adjust between 0,08 and 0,22 mm between the gears tooth but only when there is only 1 ring was used that can be happen in a rare case. the drawing is to find also by bosch in america the partnumbers are the same.
http://www.powertools-aftersalesservice.com/public/boschprof/service?p_auth=ZdEJ7pFj&p_p_auth=R78yYhDo&p_p_id=WSRP_bc93764e__6873__4b00__9a29__b331c9759da9&p_p_lifecycle=1&p_p_state=normal&p_p_mode=view&_WSRP_bc93764e__6873__4b00__9a29__b331c9759da9_wsrp-navigationalState=L0JPUy9QVEFTLVBULVNJUy1TaXRlL25sX05MLy0vRVVSL1ZpZXdQcm9kdWN0LURpc3BhdGNoO3BnaWQ9YmI5NWI3MGRjM2E3NzQxY2ExYzA0OGYyM2IzMDdhNWQ4RkJCO3NpZD1Zdks0RVZOU3dzVm1OZ3M3YnNlazZselpkRGtMODVwSi1QTTd1dEh5ZERrTDg1cEotUE09

Bosch 1 916 SDS... | Answered on Aug 20, 2019

1 Answer

Generator shutdown after some time

I think there is some faults to cause the generator stop, focus on checking the oil circuit, gas path and generator load.

https://www.dieselgeneratortech.com/diesel-generators/faults-caused-by-low-load-operation-of-diesel-generator.html

Hammering | Answered on Aug 09, 2019

1 Answer

I am looking for a manual of the detroit demolition breaker 1700W

It's an Australian brand. Phone here
https://www.totaltools.com.au/catalog/product/view/id/22431/s/123227-detroit-1700w-30mm-hex-demolition-hammer-detddh1700/category/615

It will be similar

https://www.toolex.com.au/ts1521004019/attachments/Product/107326/592720.tag.ins.pdf

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&ei=T74vXZrRCoyGsAXIuovwCw&q=detroit+demolition+1700W+manual

Hammering | Answered on Jul 18, 2019

1 Answer

Where do you fill the oil in the chipping hammer

See all the videos
https://www.google.com/search?q=fill+the+oil+in+the+chipping+hammer

Hammering | Answered on Jul 18, 2019

1 Answer

Where can I repair my Bosch gsh 10c is not hammering

Click on this link and Google will find someone close to you or Google

(your city) bosch power tool repairs

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&ei=H7ovXdj9Ns2ItQXevKfoBg&q=bosch+power+tool+repairs

Bosch Hammering | Answered on Jul 18, 2019

1 Answer

Where can I get a set of brushes for a kango 950X

eBay or Amazon

https://www.amazon.ca/Carbon-Brushes-Kango-9170003049-Breakers/dp/B00NMCBZQG

https://www.ebay.co.uk/itm/Kango-9170003049-Carbon-Brushes-for-750X-900-900X-900KV-950-950X-950K-900s-990-/261127191695

https://www.mrcarbonbrush.com/Kangos_900_900X_900KV_950_950X_950KV_990_900S/p2644628_12014706.aspx

https://www.google.com/search?q=brushes+for+a+kango+950X

Hammering | Answered on Jul 18, 2019

1 Answer

Which type of oil for rok demolition hammer thank you

If an oil sight glass is in the modelrange of the brand ROK Rottela 40 , but if no sight glass is used in the model then often is to use special Grease lubrication. or only an special volume of oil and most used of them are zinc-free hydraulic based and included in the manual instructions of a maintenance set (service kit)wear parts set.

Hammering | Answered on May 29, 2019

1 Answer

I have the Endurance 300

If it's like mine, it probably won't charge. First time I let it run down, it was screwed, a real POS.

Black & Decker... | Answered on May 19, 2019

1 Answer

Does anyone have wiring diagram for on/off switch on kango Bosch GSH27 please?

Fixya is not a chat group. Contact Bosch directly to inquire.

Bosch Hammering | Answered on Apr 29, 2019

1 Answer

Hi any body know anything about kango 750 like where I can get a manual

https://webservice.ttigroup.eu/local/uploaded/catalog/414-917---700S-750S.pdf

https://www.milwaukeetool.eu/7-kg-class-drilling-and-breaking-hammer/k-750-s-eu/

Hammering | Answered on Apr 28, 2019

1 Answer

What lube oil is used on your xtrementpowerUS Demolition Electric jack hammer 1000w

WHAT DOES YOUR MANUAL TELL YOU ? ASK Google OR LOCAL RETAILER .OR MANUFACTURER'S WEBSITE

Electric... | Answered on Apr 28, 2019

1 Answer

I received my Xtreme Jack hammer 2200W Demolition Hammer. How much oil (quantity) do I put in and where do I fill it?

3 to 4 ounces for first fill. You actually unscrew the oil gauge with the little wrench that should have come with the tool and add the oil there. After putting the cap back on, hold the tool upright to check the oil level. Check daily and add oil when the level drops to 1/4 when checking as described above.

Hammering | Answered on Apr 05, 2019

1 Answer

Kango 950 does not hammer.motor is working, gears are ok. I have dismantled machine and cannot see anything broken

kango 950 was the hammer drill version. Usually when they stopped hammering they were due for a rebuild. These units have a aluminum piston that rides in a steel tube striker. When the 2 rubber piston rings wear out you will get the described problem. The Kango's use a special tan grease so you cannot just yank it apart and replace the 2 rings with o-rings and grease. I had to rebuild 15 900 and 950's because the previous mechanic used the wrong grease. https://project21designs.com/kango-950-parts
The link sells grease & rings.

Hammering | Answered on Mar 13, 2019

1 Answer