Blenders - Recent Questions, Troubleshooting & Support


ASK THE MANUFACTURER WE HAVE NO IDEA HERE

Blenders | Answered 8 hours ago


Replacement parts for Wolfgang Puck Immersion Blenders are available here:

http://www.wpcookware.com/categories.asp?cat=26

If you do not see the model number for your product or parts are not shown, suggest you contact their Customer service at 1-800-275-8273 to determine if the required replacement part is available for your model. Alternatively try making an inquiry via their webform:

http://www.wpcookware.com/contact.asp

Wolfgang Puck... | Answered 11 hours ago


I'm not familiar with that model number but if it is rubber with fingers sticking up then a large flat screwdriver under it and lever it up, bending it a little from 2 different sides and you should then be able to unscrew it (left hand thread I think) with your fingers. Failing that put in extra effort and wreck it off, the threaded part is aluminum and not strong enough to cause any damage to the motor shaft.
If the coupling is internal splines in a hole ask me another question.

KitchenAid KSB5... | Answered Yesterday


I'm not familiar with that model number but if it is rubber with fingers sticking up then a large flat screwdriver under it and lever it up, bending it a little from 2 different sides and you should then be able to unscrew it (left hand thread I think) with your fingers. Failing that put in extra effort and wreck it off, the threaded part is aluminum and not strong enough to cause any damage to the motor shaft.
If the coupling is internal splines in a hole ask me another question.

KitchenAid KSB5... | Answered Yesterday


Contact your local Kitchen Aid service agent

KitchenAid... | Answered Yesterday


Fixya does not sell VillaWare parts.

VillaWare... | Answered 2 days ago


It Could Be a Number of Things..
It's most likely that the electrical Wire Could Have a Shortage, If it cuts off again Try gently Wiggling the Electrical Wire in a Number of Directions If it cuts on and off while your fidgeting with it, you've found your Problem! A quick fix would be to Adjust the wire In the position it would cut on the strongest, wrap the cord with Tape to Keep the wire in that Position, this will Prevent it from shorting again.
Either that or you simply put too much product in the Blender with an inadequate amount of liquid.

Blenders | Answered on Oct 06, 2019


Why do you need to get into it? All Braun products have locking clips along the split edge. You need to use a plastic 'bludger'. Better to take it to a Braun Service Centre.

Braun Blenders | Answered on Sep 16, 2019


typically, you can't repair it.

Blenders | Answered on Sep 14, 2019


that would be a function of the container. Just a guess, why would it not handle hot & cold? Obviously if it were glass I would say yess. If plastic contacts the liquid, then maybe/maybe not.

Moulinex... | Answered on Sep 14, 2019


it is probably covered in your manual. They are all slightly different.

Hamilton Beach... | Answered on Sep 14, 2019


If you think you need to replace it, first make sure you can get the part.
then look for a parts breakdown at an online parts store. If that doesn't help you will have to hunt and peck to figure it out. Do not be too aggressive, though after all these years things will be stuck.

Waring Blenders | Answered on Sep 14, 2019


that happens to the best of them. Try heat soap, vinegar, and a tight grip to get it off.

Blenders | Answered on Sep 14, 2019


blenders are:
power cord, switch, speed control, and motor.
A disassembly and VOM meter is required to determine which part is defective.

Blenders | Answered on Sep 14, 2019


Hiya,

Sorry to hear you are experiencing an issue with your blender. We believe that the described issue indicates control board fault.

If you have KSB555, please follow the link below to show you how to replace this part on your appliance.

https://www.kaparts.co.uk/Help/KitchenAidHelp/KitchenAidBlenderHelp/HowtochangetheControlBoardonaKSB555/tabid/650/Default.aspx

https://www.youtube.com/watch?v=Lafh8UGn4No

Hope you found this useful :-)

KitchenAid... | Answered on Sep 12, 2019


how to tighten nut on kitchen aid blender

KitchenAid... | Answered on Sep 12, 2019


Use https://www.google.com and the words manual and whatever manufacturer and model it is to see manuals.

Blenders | Answered on Sep 11, 2019

Not finding what you are looking for?
Blenders Logo

6,196 questions posted

Ask a Question

Usually answered in minutes!

Top Blenders Experts

eyecam

Level 2 Expert

96 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Ross Keen

Level 3 Expert

1355 Answers

Are you a Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...