Question about Summit Refrigerators

1 Answer

I just punchered a tiny hole on the side of the u shaped coil & all the freon blew out,wheres best place to replace that part. My kegerator is a summit sbc-500ss model. Heres a pic attached. Thx

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Summit Master
  • 56,071 Answers

Plan on replacing the unit .

Posted on Nov 09, 2015

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
rohntech
  • 422 Answers

SOURCE: I have a summit

I think your right. So check that relay located in the compressor. It has covered so remove the cover and see if the relay has deformity. Also check the overload protection, a similar problem will also cause it- turn on and off it that is near to be defective. You will need a tester for testing that parts.
Nice to help you.

Posted on Jul 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove stuck screw from crankcase coveron '83 Honda c110 motorcycle


Hi! if you don't have a hammer-screwdriver (what is the right name?) just use a puncher + hammer: on the side of the head first punch a small hole, so the tip of the puncher is well held on that spot/hole. Then carry on with the puncher a bit off-axis (of the screw), to cause the screw to rotate a bit to the left. Then carry on. Some WD40 can help too. I got some great results like that. Good luck!

Aug 17, 2014 | 2005 Honda Shadow Spirit 750

1 Answer

Kegerator no longer running cold


You need a new start device if your compressor is not running/pumping.That is the box on the side of the compressor .If you can put your hand on the compressor to make sure it (compressor) is than you have a Freon leak. The small line copper coming off the compressor should be between 75 & approximately 85 if its not ho you have Freon leak somewhere.

Nov 15, 2013 | Nostalgia Electrics Kegerator Beer Fridge

1 Answer

Is there a universal standard for hole punchers?


No there isn't, there are many different hole punchers that make holes at different spaces apart and different countries use different hole spacings.

Wikipedia has a chart of all the different hole punchers. http://en.wikipedia.org/wiki/Hole_punch#Chart.5B3.5D

Sep 22, 2013 | Office Equipment & Supplies

1 Answer

My Lavazza Blue coffee machine does not press enough to punch the holes. The coffee comes out water. What should I do.


After 1700 shots it is recommended that both upper and lower punchers as well as all seals in the brew unit be replaced. These punchers are only plastic so they do get worn down after much use. You may also be experiencing more water in your drawer as water is leaking from around the capsule seal. This is also an indication that the seals and punchers should be replaced. Given where you go to have this fixed, the parts may cost less than $15.00.

Jul 08, 2011 | Lavazza 2210

2 Answers

My Kitchenaid refrigerator stop freezing. It still gets cold on both sides. But the freezer does not freeze anymore. I was told that it was the coils need cleaning, so I blew them ouy with my air...


It could be a freon leak, or the compressor is not staying on.  If you can hear a clicking sound coming from the back every couple of minutes, your compressor overload is kicking off.  More than likely you either have a freon leak, or a defective compressor. Check the warranty on your machine as many manufactures warranty the sealed system for much longer than the rest of the refrigerator.

Nov 03, 2009 | KitchenAid Superba Architect KSCS25INSS...

2 Answers

Build in kitchenaid, freezer working but not freezing


This video I made how to change evaporator on Thermador refrigerator, which is just copy of of Build in Kitchenaid. Problem was that it was running, but ice cream never got frozen. I checked pressures, was low on freon. I checked evaporator coils - found out that defrost heater got deformed and was touching evaporator coils - so it burned holes, where freon started to leak.( I think it designed not best way). Defrost heater on this fridges way to close to evaporator coils. Check this video to get an idea what Im talking about. I hope That helps u to understand why this repair is so expensive and what causing it.

May 08, 2009 | KitchenAid KSCS25FKSS Side by Side...

2 Answers

Beverage-Air Kegerator Not Staying Cold


It can take a very long time to get a keg of beer down in temperature. The heat transfer from a keg is slow due to the lack of air circulation inside the keg. You should also check your condenser coils, make sure they are clean. Door gasket should also be in good repair. Hope this helps.

Jan 20, 2009 | Beverage-Air Kegerator - Beer Keg Cooler...

2 Answers

Leak repair Samsung window air conditioner


Modern window units intentionally do not allow the water to drain directly, they want the fan blade to sling the water on to the condensor (the coil that is outside) to aid in cooling actually helps the unit cool better in high outside temps, it also evaporates it this way, depending on where the hole was drilled it may be able to be repaired, if it was just a copper tube it will be less expensive than replacing the whole coil. Since its a relative inexpensive unit anyway the labor and freon may be more than its worth. Lesson learned dont drill a hole in the base it lowers it's efficiency and can lead to a punctured freon line.

Sep 29, 2007 | Heating & Cooling

Not finding what you are looking for?
Refrigerators Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Summit Refrigerators Experts

Lawrence Oravetz

Level 3 Expert

10478 Answers

ray gallant

Level 3 Expert

56049 Answers

Tom Chichester

Level 3 Expert

49110 Answers

Are you a Summit Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...