Question about 2002 Chevrolet Malibu

1 Answer

3.1 v6 location of crankshaft position sensor at rear of engine. have the exhaust crossover off and other parts as well.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,092 Answers

CRANKSHAFT POSITION SENSOR IS BEHIND CRANKSHAFT PULLEY.YOU HAVE TO REMOVE CRANKSHAFT PULLEY TO REPLACE THE CKP SENSOR.

Posted on Jun 19, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Crankshaft Position Sensor located on a 2008 Cadillac SRX AWD 3.6L v6 engine and how do I get to it ?


Crankshaft Position Sensor Replacement
Removal Procedure
Turn the ignition OFF.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
Remove the exhaust manifold heat shield to obtain access.

Sep 25, 2018 | Cadillac Cars & Trucks

1 Answer

Where is the crankshaft sensor located on a 2010 Chevy Impala 3.5 v6


3.5L (LZ4) & 3.9L (LZ9) Engines

The Crankshaft Position (CKP) sensor is located on the right side of the engine, above the transaxle and just below the exhaust manifold

May 18, 2018 | Cars & Trucks

1 Answer

Where is the crankshaft sensor on a 2007 saturn outlook xr 3.6 ive been lookinh for 3 days and im seeing to many different locations online


Crankshaft Position (CKP) Sensor (LY7)
Left side of engine compartment, lower rear of engine block, above transmission

Remove the exhaust manifold lower heat shield. Refer to Exhaust Manifold Lower Heat Shield Replacement .
Disconnect the engine wiring harness electrical connector (3) from the crankshaft position (CKP) sensor (4).

Jan 15, 2018 | Saturn Cars & Trucks

1 Answer

How many crankshaft position sensors are on a 1998 buick century 3100 engine and locations


Two crankshaft position sensors .
Crankshaft Position (CKP) Sensor (7X)
Lower rear of the engine block, below the exhaust manifold

Crankshaft Position (CKP) Sensor (24X)
Right side of the engine, at the end of the crankshaft, behind the harmonic balancer

Jul 10, 2017 | Buick Cars & Trucks

2 Answers

Replace crankshaft position sensor in 2003 dodge caravan 3.3 V6


According to Haynes, the V6 engine has the sensor mounted in the bellhousing on the back of the engine.

Aug 20, 2012 | Dodge Cars & Trucks

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

1 Answer

WHERE IS THE CRANK SHAFT SENSOR LOCATED


The 2002 Santa Fe came with three (3) possible powertrains (engines). The 4 cylinder, and two different V6 engines - i.e. 2.4L 4 cylinder, the 2.7L V6 and the 3.5L V6.

The crankshaft position sensor on the 4 cylinder and the 3.5L V6 are in the same place - Front Crank Shaft behind the pully (behind the timing belt cover.

On the 2.7L V6, the Cranshaft Position Sensor is located in the engine block (Left Hand Side)
near the flywheel (adjacent to the LH (Bank 2) exhaust manifold.

Note: Left Hand Side means the radiator side (front) Bank 1 is the firewall side.

Jun 30, 2011 | 2002 Hyundai Santa Fe

2 Answers

Can u please give me an idea where is the crank shaft sensor really located at on a 98 dodge plymouth voyager


3.0 3.3 and 3.8 liter engines look down on the back side of the engine on the firewall side. It will be under the crossover exhaust pipe and bolted to the transmission. It will have three wires going to it.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Dec 08, 2010 | 1998 Plymouth Voyager

1 Answer

Where is the crankshaft sensor located on the dodge dakota 99 sport v6


On the V6 and V8 engines, the crankshaft position sensor is bolted to the cylinder block near the rear of the right cylinder head.

2e977ab.jpg

Jul 30, 2010 | 1999 Dodge Dakota

1 Answer

Replace oxygen sensor a 94 Olds Cutass Ciera S 3.1 V6 Engine where is it located. Roy M F


it should be in the exhaust manifold, if not just below the manifold in the exhaust header pipe,

ACDELCO Part # AFS75
SENSOR,HTD OXY(POSN 1) IN EXH MANIFOLD/CROSSOVER

Sep 04, 2009 | 1989 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
2002 Chevrolet Malibu Logo

909 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...