Question about 2000 Chevrolet Silverado 1500

5 Answers

00 Chevy Silverado... ABS EBCM diagram help??? Brake line hookups

00 Chevy Silverado... ABS EBCM i had to replace some brake lines and i am unsure if i reconnected them back to there proper spot on the Unit i have 5 lines ... 2 from Master cylindar 1 driver front 1 passenger front and 1 rear brake line where do they go.? Can't seam to find a diagram on where they go..

Posted by on

  • 3 more comments 
  • Anonymous Aug 28, 2009

    I'm not sure if i understand that diagram you replied with.

    (1)...(2)...(3)
    (4)...(5)
    (C)...(C)

    C = Capped

    __ Front Master Cyl.Brake Line
    __ Rear Master Cyl. Brake Line
    __ Front Drivers Brake Line
    __ Front Pass. Brake Line
    __ Rear Brake Line

    I need to know which one goes to which connection of that diagram i made. cause i had to disconnect all to get to the 3 connection to replace that brake Line cause the transfer case and tortion bar were in the way to get anything in right with out taking them out.. I;m 99% sure #3 is the rear brake line connection cause that on was what i needed to replace.. i have no orginal brake lines now except the brake lines that come from the T connection of the rear brake line system.

  • Anonymous Aug 28, 2009

    I'm not sure if i understand that diagram you replied with.

    (1)...(2)...(3)
    (4)...(5)
    (C)...(C)

    C = Capped

    __ Front Master Cyl.Brake Line
    __ Rear Master Cyl. Brake Line
    __ Front Drivers Brake Line
    __ Front Pass. Brake Line
    __ Rear Brake Line

    I need to know which one goes to which connection of that diagram i made. cause i had to disconnect all to get to the 3 connection to replace that brake Line cause the transfer case and tortion bar were in the way to get anything in right with out taking them out.. I;m 99% sure #3 is the rear brake line connection cause that on was what i needed to replace.. i have no orginal brake lines now except the brake lines that come from the T connection of the rear brake line system.

  • Anonymous Mar 14, 2014

    00 CHEVY SILVERADO BANK 2 SENSOR 2

  • Anonymous Mar 18, 2014

    what size brake line is on the 202 chevy silverado 1500 2wd

  • Anonymous Mar 29, 2014

    1999 Chevy Silverado 1500 show me diagram of rear passenger brake caliber an bracket along with roter an brake pads

×

Ad

5 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 140 Answers

Hello,
I hope this helps.






00 Chevy Silverado... ABS EBCM diagram help??? Bra - 1ec2f93.jpg
Thank You,
Roy

Posted on Aug 28, 2009

  • 2 more comments 
  • Roy Funkhouser
    Roy Funkhouser Aug 29, 2009

    Hello,

    Ok here is an idea since there is no other diagram. The two inputs are larger than the three outputs. Install the inputs and allow fluid flow from only one resivior determine if its the front or rear resivior and cordinate it with the correct output. Let me know how it works. I am sorry the diagram isn't better.



    Thank You,

    Roy

  • Roy Funkhouser
    Roy Funkhouser Nov 17, 2009

    Hello,

    Have you got any of the old lines? Some times it helps to put them in place just to see where they should go. Just a thought. I am sorry it took so long to get back with you. I have been looking to find a more through answer but to no avail.



    I hope this helps,



    Roy

  • gwenholbrook
    gwenholbrook Jun 18, 2012

    inlarge it

  • Roy Funkhouser
    Roy Funkhouser Jan 11, 2015

    http://i.fixya.net/uploads/images/1ec2f9...

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

(1)...(2)...(3)
(4)...(5)
(C)...(C)

C = Capped

_5_ Front Master Cyl.Brake Line
_4_ Rear Master Cyl. Brake Line
_2_ Front Drivers Brake Line
_1_ Front Pass. Brake Line
_3_ Rear Brake Line

just got done redoing all the brake line on a chevy silverado 1500 ex-cab 4x4 5.3L vortec and this is what i figured out for the abs block

Posted on Apr 23, 2012

  • mr_nice_guy4
    mr_nice_guy4 Apr 23, 2012

    (1)...(2)...(3)
    (4)...(5)
    (C)...(C)

    C = Capped

    _5_ Front Master Cyl.Brake Line
    _4_ Rear Master Cyl. Brake Line
    _2_ Front Drivers Brake Line
    _1_ Front Pass. Brake Line
    _3_ Rear Brake Line

    just got done redoing all the brake line on a chevy silverado 1500 ex-cab 4x4 5.3L vortec and this is what i figured out for the abs block

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Looking from vehicle front to rear, here is the layout:
There are three connections along the top. From left to right, the connections are Front Left Wheel, Front Right Wheel, and the Connector near Left Rear Wheel that serves both rear wheels. The bottom two connections go to the Master Cylinder. The Left Connection goes to the rear Master Cylinder Connection and the Right Connection goes to the front Master Cylinder Connection.
Remember that the end flare connections to the vehicle must be double flares.

Posted on Dec 11, 2011

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Following Frank's advice this is what I found on my truck...

This is the ABS EHCU layout:
(1)...(2)...(3)
(4)...(5)
(C)...(C)

C = Capped

_5_ Front Master Cyl.Brake Line (which controls the rear brakes)
_4_ Rear Master Cyl. Brake Line (which controls the front brakes)
_1_ Front Drivers Brake Line
_2_ Front Pass. Brake Line
_3_ Rear Brake Line

Posted on Nov 02, 2012

  • Rodger Gibbr
    Rodger Gibbr Sep 29, 2015

    There are two different answers concerning the front brakes. Which s correct?

×

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

This was a lifesaver, my diagram got wiped out by the rain and i was going to do it off memory. i was correct, but it was nice to have this as confirmation. glad this PITA job is DONE!

Posted on Jul 09, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 chevy silverado check engine light code CO201


ABS code not check engine light code .
DTC C0201 00: Antilock Brake System (ABS) Enable Relay Contact Circuit
The solenoid relay, located within the electronic brake control module (EBCM), supplies battery voltage to all of the valve solenoids.
Circuit/System Verification
With scan tool installed, clear the DTCs then drive the vehicle in a straight line at a speed greater than 20 km/h (13 mph). If the DTC did not set as a current DTC see diagnostic aids.
Circuit/System Testing
Test for an open or a short to ground in the battery positive voltage circuit to the EBCM. Verify no open or a short to ground is found.
Test the EBCM ground circuit, an open or high resistance.
? If an open or a short to ground is found, repair the circuit.
Replace the EBCM assembly.

DTC C0201 (Equal to or over 8600 GVW)
The system relay, located within the electronic brake control module (EBCM), supplies battery voltage to all of the valve solenoids and to the Antilock Brake System (ABS) pump motor. When the relay contacts close, the EBCM monitors the voltage supplied to the valve solenoids and compares this voltage to monitored ignition voltage.
Action Taken When the DTC Sets
• The EBCM disables the ABS/DRP.
• The ABS indicator turns ON.
• The brake warning indicator turns ON

Aug 08, 2017 | Cars & Trucks

1 Answer

Find location of EBCM replacement on a 2001 Chevy Silverado HD 2500


The EBCM is located on the drivers side frame rail under the truck. There are 5 brake lines that run into the unit.

Aug 04, 2013 | Chevrolet Silverado Cars & Trucks

1 Answer

Locate ebcm on a 2004 silverado


the ebcm is located under the truck on top of the bpmv (abs motor) almost under the drivers seat attached to the frame is the abs unit you will see all the brake lines hooked to it. the ebcm is bolted to the top of unit

Sep 23, 2011 | 2004 Chevrolet Silverado

1 Answer

I have a 2001 chevrolet silverado with the following codes C0265,CO241 C0245 C0246 CO251. ABS & BRAKE LIGHT COME ON AND OFF Thanks Joey


looks like you need an ebcm. You can check the ground under the drivers side door attached to the frame, make sure it is clean and tight.



DTC C0241-C0254 or C041-C054
Circuit DescriptionThe ABS relay supplies battery voltage to 6 valve solenoids. The electronic brake control module (EBCM) microprocessor applies the grounds needed to activate each solenoid. The low side of each solenoid coil has a feedback circuit to the EBCM microprocessor. When a solenoid is commanded OFF, the feedback voltage is high. When a solenoid is commanded ON, the feedback voltage is low.
Conditions for Running the DTC • The ignition is ON. • The vehicle speed is greater than 6 km/h (4 mph). Conditions for Setting the DTCThe EBCM detects an internal malfunction.
Action Taken When the DTC Sets C0241, C0242, C0245, C0246, C0251, C0252, C0253, C0254If equipped, the following actions occur:
• The EBCM disables the DRP/ABS. • The ABS indicator turns ON. • The red brake warning indicator turns ON. C0243, C0244, C0247, C0248If equipped, the following actions occur:
• The EBCM disables the ABS. • The ABS indicator turns ON. Conditions for Clearing the DTCThe conditions for setting the DTC are no longer present and you use the scan tool Clear DTCs function.
Diagnostic AidsAn intermittent open/shorted solenoid DTC can be set by several different internal EBCM problems. Replace the EBCM if an open/shorted solenoid DTC continues to set intermittently.
Step
Action
Yes
No
1
Did you perform the ABS Diagnostic System Check?
Go to Step 2
Go to Diagnostic System Check - ABS
2
  1. Use a scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC set?
Go to Step 3
Go to Diagnostic Aids
3
Important: Following EBCM replacement, use the scan tool to perform the Tire Size Calibration procedure and the Trim Level Calibration procedure, if applicable.
Replace the EBCM. Refer to Electronic Brake Control Module Replacement .
Did you complete the replacement?
Go to Step 4
--
4
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?
Go to Step 3
System OK

Jul 29, 2011 | 2001 Chevrolet Silverado 1500

2 Answers

Brake line on chevy silverado broken,need diagram to follow line back to box in middle of truck


Brake line diagrams dont exist like wiring diagrams do. If your truck has ABS, that's the ABS controller, and if not it's just the proportioning/metering valve.

Apr 27, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

I have a 94 chevy caprice classic wagon. it had sat for 3 years before i bought it. when it was last driven everything worked.after i purchased it the abs light on the dash was on. i noticed fluid leakage...


Hello! One of the wheel sensors is probably defective ...They back themselves out of their mounting...Or the wheel hub reluctor is rusted...you have a couple of options...Pull the INDIC fuse (10A) from the interior fuse box turning off the light...Power down the EBCM by pulling the PCM/IGN fuse # 5 (30A)...Drive and see if you notice any ill effects...If not, the ABS is disabled...

Wheel Sensors are; Left Front...Right Front...And Rear Axle...Guru...Saailer

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

Jan 12, 2011 | 1994 Chevrolet Caprice Classic

1 Answer

How to trouble shoot the brake system?


To trouble shoot the brake system you have to check:AntiLock Brake System ABS:
Hydraulic Modulator
Basically this unit holds steady or bleeds off pressure in brake line, as necessary, when the Electronic Brake Control Module (EBCM) detects an abnormal deceleration in the speed of the wheel. On 2000 and later models the EBCM and Brake Pressure Modulator Valve (BPMV) are mounted on a bracket attached on the left strut tower.
Wheel Speed Sensors, brake fluid level, brake hoses and lines, inspect and replacement, Brake hydraulic system-bleeding, Brake light switch, check, adjustment and replacement.
Disk brake caliper, disk brake pads, drum brake shoes, master cylinder, master cylinder reservoir, O-rings replacement, parking brake adjustment, parking brake cables inspect and replacement, parking brake shoes-replacement, power brake booster, check or replacement, wheel cylinder inspect and replace.

Oct 10, 2010 | 2000 Chevrolet Venture

Not finding what you are looking for?
Cars & Trucks Logo

32,720 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...