Question about Chevrolet Cars & Trucks

1 Answer

How do i remove the center pillar trim panel on a 2016 chevy colorado

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Chevrolet Expert
  • 220 Answers

Ensure that there are no screws going up into the dash. Now simply pull. The spring-loaded retainers just pop out.

Posted on May 01, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 102 Answers

SOURCE: whow to remove center trim panel on dash board for

on the dash top the center section is removed by holding tightly from the sides and slide it toward the windshield until it unlatches. if you mean the one around the radio , it is most of the dash face and has 2 screws at top of instrument cluster and 2 more hiding at the bottom under the the a/c controls way back just above the very front of center counsel.

Posted on Mar 31, 2009

  • 1986 Answers

SOURCE: Removal of door panel/trim

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 66 Answers

SOURCE: How do I replace the convertible pillar post

no,pull the weatherstrip back nearer the windshield and there are screws hidden under there>

Posted on Oct 27, 2009

  • 149 Answers

SOURCE: remove 2004 Dodge Grand Caravan D-pillar panel

To remove the panel completely. You must remove all screws & the seatbealt bolts for the 2nd & 3rd seats

Posted on Jan 20, 2010

  • 91 Answers

SOURCE: How to remove the car stereo from 2007 Chevy Colorado

This is not hard but tricky because the trim plate around the radio has clips that hold the trim plate very tight.Use a plastic type flat tool or flat screw driver wraped with tape or a shop rag to avoid damage to the plastic trim and pry the trim panel around the radio loose. remove all elec connectors.Then remove the screws that hold the radio in place and remove all elec connectors.

Posted on Feb 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing quarter glass on left side on 2005 pontiac gto


Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

Dec 23, 2016 | Pontiac Cars & Trucks

1 Answer

How to disconnect a BCM in a chevy colorado 2007


Removal Procedure
Important:
• The ignition switch should be in the OFF position when connecting or disconnecting the connectors to the body control module (BCM).
• Always disconnect the black body wiring harness connector FIRST and the gray instrument panel (I/P) wiring harness connector LAST.
• Always connect the black body wiring harness connector FIRST and the gray I/P wiring harness LAST.
• Do not open the BCM housing. The module does not have any serviceable components. The module may be replaced only as an assembly.
Ensure the ignition switch is in the OFF position.
Remove the right front hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement - Right Side .
Disconnect the body wiring harness electrical connector (1) from the BCM.
Release the fastener retaining the body wiring harness electrical connector to the BCM. Remove the 2 fasteners retaining the BCM to the hinge pillar.
Remove the BCM from the hinge pillar by unlocking the integral tab.
Remove the BCM from the vehicle.
If installing a replacement BCM, program the BCM. Refer to Control Module References .

Dec 19, 2016 | Cars & Trucks

1 Answer

How to install quarter window that flips out on 2003 dodge Dakota. 2 door.right side


REMOVAL

(1) Remove quarter trim panel.

(2) Remove the bolts attaching the latch to the cab


side panel.



(3) Remove the nuts attaching the frame/hinge to

the B-pillar.

(4) Remove the glass from the cab.
(5) If necessary, remove the latch from the glass.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

Oct 02, 2016 | 2003 Dodge Dakota

2 Answers

How easy is it to change a heater core in a2003 Kia sedona


It is in no way easy. But if you want to try, here are the instructions....

3.5L Engine
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the heater hoses.
  5. Remove the driver air bag module.
  6. Remove the steering wheel.
  7. Remove the turn signal assembly.
  8. Remove the upper and lower steering column covers.
  9. Remove the A-pillar upper trim.
  10. Remove the instrument cluster trim.
  11. Remove the instrument cluster.
  12. Remove the A-pillar lower trim.
  13. Remove the hood release handle.
  14. Remove the left lower trim panel.
  15. Remove the multi box.
  16. Remove the audio panel.
  17. Remove the ventilation control panel.
  18. Remove the radio.
  19. Remove the glove box.
  20. Remove the center console.
  21. Remove the audio system speakers and mounting bolts from the top of the instrument panel.
  22. Remove the side covers.
  23. Remove the T-bar mounting bolts.
  24. Remove the bottom mounting bolts.
  25. Remove the instrument panel wiring harness connectors.
  26. Remove the instrument panel.
  27. Remove the heater unit.


26096060-nraukxomtaildozoxjjbr22p-1-0.gif 26096060-nraukxomtaildozoxjjbr22p-1-1.gif

To install:
  1. Install the heater unit.
  2. Install the instrument panel.
  3. Connect the instrument panel wiring harness connectors.
  4. Install the bottom mounting bolts.
  5. Install the T-bar mounting bolts.
  6. Install the side covers.
  7. Install the upper mounting bolts and audio system speakers.
  8. Install the center console.
  9. Install the glove box.
  10. Install the radio.
  11. Install the ventilation control panel.
  12. Install the audio panel.
  13. Install the multi box.
  14. Install the left lower trim panel.
  15. Install the hood release handle.
  16. Install the A-pillar lower trim.
  17. Install the instrument cluster.
  18. Install the instrument cluster trim.
  19. Install the A-pillar upper trim.
  20. Install the upper and lower steering column covers.
  21. Install the turn signal assembly.
  22. Install the steering wheel.
  23. Install the driver air bag module.
  24. Install the heater hoses.
  25. Connect the negative battery cable.
  26. Fill the cooling system.
  27. Start the engine and check for leaks and proper heater operation.

Feb 15, 2016 | Kia Cars & Trucks

1 Answer

Where are drains located on a 2003 chevrolet impala sunroof?


They go down inside front A pillar an inside rear D pillar . To get at them you need to take trim off an the headliner down .
Sunroof Housing Rear Drain Hose Replacement (Impala)
Remove the headliner. Refer to Headlining Trim Panel Replacement in Interior Trim. Remove the rear quarter lower trim panel. Refer to Rear Quarter Lower Trim Panel Replacement in Interior Trim. Disconnect the rear sunroof drain hose from the sunroof module rear spigot. Remove the tape from the rear sunroof drain hose tube.
Disconnect the rear sunroof drain hose from the rear sunroof drain hose tube. Remove the rear sunroof drain hose tube from the upper retainer clip. Remove the rear sunroof drain hose from the rear pillar
The front is simalier .

Dec 22, 2015 | 2003 Chevrolet Impala

2 Answers

How many airbag sensors in a 2008 gmc acadia


1) Front End Sensor - Right--Located under the front hood in the engine compartment (2) I/P Air Bag--Located at the top right under the instrument panel (3) Roof Rail Air Bag - Right--Located under the headliner, extending from the passenger front windshield pillar to the passenger rear windshield pillar (4) Side Impact Sensor (SIS) - RF--Located under the right front door trim near the lower rear of the door frame (5) Sensing and Diagnostic Module (SDM)--Located underneath the vehicle carpet under the center console (6) Seat Belt Pretensioner - RF--Located under the trim near the bottom of the center pillar (7) Side Impact Sensor (SIS) - RR--Located under the right rear door trim near the lower rear of the door frame (8) Roof Rail Module - Right--Located behind the garnish molding on the upper rear pillar (9) Roof Rail Module - Left--Located behind garnish molding on the upper rear pillar (10) Side Impact Sensor (SIS) - LR--Located under the left rear door trim near the lower rear of the door frame (11) Seat Belt Pretensioner - LF--Located under the trim near the bottom of the center pillar (12) Side Impact Sensor (SIS) - LF--Located under the left front door trim near the lower rear of the door frame (13) Roof Rail Air Bag - Left--Located under the headliner, extending from the driver front windshield pillar to the driver rear windshield pillar (14) Steering Wheel Air Bag--Located on the steering wheel (15) Vehicle Battery--Located at the front left of the engine compartment. (16) Front End Sensor - Left--Located under the front hood in the engine compartment

Aug 12, 2015 | GMC Cars & Trucks

1 Answer

Where is the Parking Aid Speaker located on a 2005 Ford Explorer?


Parking aid speaker attached to the parking aid module.



  1. Remove the RH quarter trim panel. For additional information, refer to Section 501-05 .




  1. Disconnect the parking aid module electrical connector




  1. Remove the bolt and the parking aid module.




  1. To install, reverse the removal procedure


  2. The parking aid system is disabled if a fault is detected in one of the 4 sensors, the parking aid speaker, or the parking aid module. This is indicated by the parking aid disabled warning. The parking aid module is on the international standards organization (ISO) 9141 network and can be diagnosed with a diagnostic tool.



  3. Rear Quarter Trim Panel

    Removal and Installation



    All vehicles




    1. Remove the rear door scuff plate.





    1. Remove the C-pillar trim panel. For additional information, refer to C-Pillar Trim Panel in this section.





    1. Remove the D-pillar trim panel. For additional information, refer to D-Pillar Trim Panel in this section.





    1. Remove the liftgate scuff plate trim panel.



    Vehicles with third row seating




    1. Remove the third row seat. For additional information, refer to Section 501-10 .





    1. Position the liftgate opening weatherstrip aside.



    All vehicles




    1. If equipped, remove the luggage assembly cover.





    1. Remove the stowage compartment doors.





    1. NOTE: RH side shown, LH side similar.


      Remove the stowage compartment assembly.





    1. Position the carpet aside.





    1. Remove the brackets.



      • Remove the bolts.







    1. Remove the rear quarter trim panel.

Feb 26, 2015 | 2005 Ford Explorer

1 Answer

Replacing brake light above trunk on 2006 chrysler


This is quite a process....

Removal
1) Disconnect and isolate the negative battery cable.
2) Remove the rear shelf trim panel.

3ca61c4.jpg
3) Disconnect the CHMSL electrical connector (1).

7bde5c5.jpg

4) Remove the two mounting fasteners (3) to the CHMSL (2).

6793725.jpg

Installation is opposite of removal.

Rear shelf trim panel

Removal

1) Disconnect and isolate the battery negative cable.
2) Remover the right and left lower and upper C-pillar trim.
3) Remove the nut that secures the center rear seat belt lower anchor to the stud on the floor panel and feed the seat belt webbing back through the opening in the top of the rear shelf panel trim (2) to the retractor.
4) Remove the push-pin fastener (1) that secures the trim (2) to the rear shelf panel.
5) Slide the trim forward to disengage the S-clip that secures the underside of the trim to the to the center of the shelf panel.
6) Remove the trim from the rear shelf panel.

24614b2.jpg

Installation

1) Position the trim (2) onto the rear shelf panel(3).
2) Slide the rear edge of the trim rearward to engage the lens bezel of the center high-mounted stop lamp and far enough to engage the S-clip that secures the underside of the trim to the center of the shelf panel.
3) Install the push-pin fastener (1) that secures the trim to the rear shelf panel.
4) Pull the center rear seat belt lower anchor and belt webbing from the retractor through the opening the the top of the rear shelf panel trim and back down to the stud on the floor panel.
5) Install and tighten the nut that secures the seat belt lower anchor to the stud on the floor panel. Tighten the nut to 34 N m (25 ft. lbs.).
6) Reinstall the right and left upper and lower C-pillar trim.
7) Connect the battery negative cable.

841a5de.jpg

C-pillar trim removal

1a140ec.jpg

5ad047d.jpg

b674bd4.jpg
cf360b2.jpg

cd4ac09.jpg
2e5b4da.jpg

Seat removal

d276bae.jpg
60b3895.jpg

469e099.jpg

087d2a6.jpg

3ad2dc9.jpg


a09baad.jpg
4981771.jpg


Hope this all gets it done for you........

Feb 23, 2010 | 2006 Chrysler 300

1 Answer

How to remove the car stereo from 2007 Chevy Colorado


This is not hard but tricky because the trim plate around the radio has clips that hold the trim plate very tight.Use a plastic type flat tool or flat screw driver wraped with tape or a shop rag to avoid damage to the plastic trim and pry the trim panel around the radio loose. remove all elec connectors.Then remove the screws that hold the radio in place and remove all elec connectors.

Jan 30, 2010 | 2007 Chevrolet Colorado (Extended Cab) New...

1 Answer

Locate heater motor 2000 chevy blazer


you have move center floor air distribution duct blower motor is behind hinge pillar trim kick panel.

Dec 10, 2009 | 2000 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...