Question about Cars & Trucks

1 Answer

Where is the crankshaft sensor located on a 2010 Chevy Impala 3.5 v6

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 84,565 Answers

3.5L (LZ4) & 3.9L (LZ9) Engines

The Crankshaft Position (CKP) sensor is located on the right side of the engine, above the transaxle and just below the exhaust manifold

Posted on May 18, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2002 chevy impala o2 location?

it is locared on the driver side on top of the transmision

Posted on Feb 27, 2009

csmock132
  • 4669 Answers

SOURCE: crankshaft sensor location and replacement procedure

It is on the rear of the engine, passenger side. You need to access it from the underside and it is halfway up the block between the head and the oilpan. It is real close to where the engine and transmission meet.

Posted on May 23, 2009

  • 2715 Answers

SOURCE: Can't find PCV valve on 2000 Chevy Impala 3.8 V6

PCV . Positive Crankcase Ventalation Valves are always located in the valve cover pans with a hose attached usually leading to the air cleaner, or some other vacuum source..

Posted on Jun 19, 2009

roniecon
  • 6927 Answers

SOURCE: were is the crankshaft position sensor located on 2001 chevy mali

It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.

Posted on Mar 22, 2010

dark_zumick
  • 2 Answers

SOURCE: 2004 3.8 Chevy impala sensor

The crankshaft positions sensor is located behind the crankwheel on the passenger side of the engine. In order to replace it or at least examine it, a person would need to remover the crankwheel with a puller that can be rented out at Autozone. Just ask for a harmonic balancer puller. Remove the front right tire and place firmly on jackstands. The crankshaft pulley WILL NOT loosen by just turning the bolt. This is a two person job. Caddycorner to the starter, there is a small plastic plate cover that covers the driveplate/flexplate. Remove the two bolts and pull the cover off. Have one person position a screwdriver into the ring gear teeth and have another remove the pulley bolt. Its EXTREMELY TIGHT and the best way to remove it is with a large rachet and a breaker bar. Once the bolt is removed, take the puller and position accoridngly. The threaded holes are not on the surface but inside the pulley itself. Place large bolt in center of the puller and place the pointed or flat tip on center of the large bolt and place. Take three very small screws or bolts that came with the puller and position all three in place. Once all this is done begin turning the bolt in the middle of the puller clockwise. This will take alot of arm strength and anywhere from 15-30 min to do. Once the wheel has come off, carefully pry off the sensor cover which is another piece of plactic. Once the cover is off, carefully remove the sensor and examine or replace as needed. Installation is reverse of removal. Hope this helps
Read more: http://wiki.answers.com/Q/Where_is_the_crankshaft_position_sensor_on_2001_Impala#ixzz1xaQZV1IR

Posted on Jun 12, 2012

Testimonial: "Thanks a lot... I'll be taking it to a shop. "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 08 Chevy Impala V6 3.5 trying to locate the crankshaft sensor


Crankshaft Position (CKP) Sensor (LZE/LZ4/LZG)
center of the engine block ( the side closest to the fire wall )

Apr 08, 2018 | Cars & Trucks

1 Answer

My 2009 chevy impala V6 has the "eva" icon flashing on the scanner. Does anyone know what does it means?


2010 Chevrolet Impala Problems, Defects & Complaints

www.carcomplaints.com/Chevrolet/Impala/2010/ The 2010 Chevrolet Impala has 60 problems & defects reported by Impala owners. ...July 11: GM Recalls 98,000 Cars For Radio and Seat Belt Problems · July .

Mar 09, 2015 | 2009 Chevrolet Impala

1 Answer

2000 chevy impala 3.8 crankshaft sensor. Where is it located?


The crank sensor is located behind the harmonic balancer on the front of the crankshaft.

Dec 29, 2010 | 2000 Chevrolet Impala

2 Answers

Were is the crank sensor located at on 2006 impala


Usually ,& depending on engine, is located on the rear side of the engine block behindthe crankshaft balancer. Good luck!

Nov 26, 2009 | 2006 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

307 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

84543 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

19466 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...