Question about 2005 Jeep Wrangler

Open Question

2005 right hand drive jeep wrangler turn signal relay location

Factory built mail jeep.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 182 Answers

SOURCE: 1998 jeep wrangler sahara brake, tail and turn signal wont work

Did you go off road in the mud or woods?If so the connecting plug where all the connect probably has gotten disconnected.I think it is near or between the fuel tank and rear bumper.

Posted on Aug 31, 2008

Ad
Mike258

Justin Case

  • 1498 Answers

SOURCE: YJ Blinker Relay

Hi there,

Both the hazard and the blinker flashers are located on the fuse panel. They pull straight out.

When both turn signals fail, the cause may be a blown fuse, a faulty flasher, a broken turn signal switch or a bad connection.

When you try the turn signals, do they light up and not blink?
-If so, probably the flasher unit.

When you try the turn signals, does nothing happen?
-Check the fuse

Let me know if the problem continues after replacing the flasher.

Mike

Posted on Aug 31, 2008

Anonymous

  • 1 Answer

SOURCE: 2005 Jeep Wrangler Unlimited cruise control will not engage.

check the vacuum line on the right side of the engine. There should be an elbow connector connecting the line to the engine. Does interior fan only come out of the defroster vents by chance?

Posted on Nov 10, 2009

Richard Scordino

  • 6982 Answers

SOURCE: 89 jeep wrangler turn signal mystery...

Two things I'd look at there...First, though it does not often happen, I'd check all turn signal bulbs to make sure that one of the filaments have not burned and re-connected themselves to the adjacent one inside the bulb. Second, you will need to do a visual check of the switch itself, to make sure the internal contacts have not melted and are not shorting to each other. Only other quick test is to remove the four way flasher and plug it in where the one for the turn signals is. If the one for the signals is burned, it possibly could do that as well. (both flashers are the same) On an 89, there aren't any "modules" so it's a fairly simple system that should not be difficult to diagnose.
Most turn out to be the switch under the steering wheel. Always make sure that all bulb sockets have a good ground.
Good luck

Posted on Dec 15, 2009

kevingsuzuki

  • 752 Answers

SOURCE: Turn signals/emergency flashers on 2001 jeep

Seating area, driver side, to the upper steering column housing at the top of the steering column, behind the multi-function switch

Posted on Feb 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Find fuse panel in 2003 jeep wrangler


jeep cherkee fuse panel is on thr right hand side front of engine bay that is near the battery good luck alan from dardanup w australia

Jul 08, 2012 | Jeep Cherokee Cars & Trucks

1 Answer

E brake wire location in 05 jeep wrangler


The e-brake switch should be right on the pedal or lever. You may have to remove some trim to get to the wiring.

Nov 29, 2009 | 2005 Jeep Wrangler

1 Answer

The hazard lights work, turn signals dont. jeep cherokee 1999


On your model,there is a separate hazard relay to the turn signal relay.On the fuse block(right-hand side kickpanel just inside the r/hand door)the upper left relay is the turn signal relay.Bottom right is for the hazards.Hope this helps you.

Oct 11, 2009 | 1999 Jeep Cherokee

1 Answer

98 jeep wrangler headlights wont turn on


I would check your headlight relay switch that is located in your steering colum

May 19, 2009 | 1998 Jeep Wrangler

1 Answer

Left flasher dead, right on works


double check your bulbs again, if still good
check your flasher

G

May 09, 2009 | 2005 Jeep Wrangler

1 Answer

YJ Blinker Relay


Hi there,

Both the hazard and the blinker flashers are located on the fuse panel. They pull straight out.

When both turn signals fail, the cause may be a blown fuse, a faulty flasher, a broken turn signal switch or a bad connection.

When you try the turn signals, do they light up and not blink?
-If so, probably the flasher unit.

When you try the turn signals, does nothing happen?
-Check the fuse

Let me know if the problem continues after replacing the flasher.

Mike

Aug 30, 2008 | 1988 Jeep Wrangler

Not finding what you are looking for?
2005 Jeep Wrangler Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...