Question about 2010 Chevrolet Equinox
Posted by Anonymous on
These sensor/s are in the air duct system going from the air filter box the the engine. It could be one sensor or two separate sensors. The MAF sensor will be as big around as the air plenum. The IAT will be a small one that plugs into the air plenum.
Posted on Sep 28, 2014
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: MAF Sensor 2004 Dodge Stratus
If your car has a MAF (Mass Air Flow) sensor, it would be located in the air delivery tube that runs from the air filter box to the throttle plate assembly on the intake manifold. It will have a wiring connector going to it, also. The MAF does exactly what it is called: It "senses" the volume, or "mass" of the air-flow; thusly it needs to be in the intake air tube. If you do NOT have such a device in the air-tube, you have a MAP sensor, (Manifold Absolute Pressure); this is another way of measuring the same air volume, albeit older technology. You will commonly find this device on the firewall, with a vacuum line running to the intake manifold.
I hope that this sheds some light on your question.
Thanks for choosing FixYa for advice!
Posted on Mar 06, 2009
Save your money, the chip is a ohm resistor at Radio Shack for under $2.00. It splices in to you IAT wire harness located at the intake tube between the air filter housing and throttle body.
Problem with this system is, that you can not adjust anything and have to run a constant 91 octane just to make sure you do not have a Detonation. The ECM will catch the Detonation from the knock sensor and compensate for it by retarding the timing which in turn lose of HP till next start up.
If you like and don't mind the check engine light on once and awhile, you can do the same by just disconnecting the IAT wire harness which give the ECM a 0 resistance thinking it's -20 out side and turn the timing up and lengths the injector pules.
When i was running a Nitro in the Toy before i sold it, i had installed a 10K ohm Potentiometer which you can buy at radio shack for under $5.00 i believe, I just spliced it in to the IAC wire harness so if i wanted to play with the Nitro I'ld turn the resistor up making the engine think it's 185 degrees F and would ****** the timing so i would not hurt the engine. But if i wanted to get more timing i would just turn the knob to drop the resistance to get more time since the engine thinks it's -20 out side.
Hope this helps. Keep me posted if you need more info. Best thing is to do a dyno tune and you can change everything right down to the Shift points.
Posted on May 29, 2009
SOURCE: Location of sensors
IAT SENSOR IS MOUNTED INSIDE INTAKE AIR HOSE TO THE AIR CLEANER ASSEMBLY. THE MASS AIR FLOW SENSOR IS ALSO MOUNTED TO THE INTAKE AIR HOSE OF THE AIR CLEANER ASSEMBLY. O2 SENSORS LOCATION.YOU HAVE 2 # O2 SENSORS.YOU HAVE ONE THE EXHAUST MANIFOLD.THE OTHER SENSOR LOCATED DOWN AT THE CATALYTIC CONVERTER.
Posted on Aug 19, 2009
Tips for a great answer:
Apr 14, 2015 | 2006 Toyota Tacoma
Apr 14, 2015 | 2006 Toyota Tacoma
Aug 08, 2012 | Chevrolet Cavalier Cars & Trucks
The Mass Air Flow (MAF) sensor/Intake Air Temperature (IAT) sensor is located in the air cleaner case.
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 34; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>
The Intake Air Temperature (IAT) sensor is an integral part of the Mass Air Flow (MAF) sensor. Looks like this:
May 12, 2011 | Nissan Pathfinder Cars & Trucks
May 22, 2010 | 2004 Mazda MPV
Apr 08, 2010 | 2004 Hyundai Elantra
Dec 16, 2009 | 2000 Mazda MPV
Jun 28, 2009 | 2002 Chevrolet Malibu
Mar 05, 2009 | 2009 Ford F-150
Jul 31, 2008 | 2005 Chevrolet Equinox
759 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: