20 Most Recent 2005 Jeep Wrangler Questions & Answers


You will get your solution and all info on service info, repair info, parts info, wiring/electrical/fuse diagrams, error/fault codes, torque specs, PCV,
owner's/service/repair/parts/maintenance manuals etc everything
this website www.reliable-store.com
it's a very good website for vehicle problems even as old as 1991 ford..

2005 Jeep... | Answered on Mar 19, 2018


Blower resistor is bad . Do you know what that is ?
Jeep Cherokee Blower Motor Resistor Replacement

2005 Jeep... | Answered on Nov 17, 2017


Have you checked the clutch master cylinder fluid level?

2005 Jeep... | Answered on Apr 04, 2017


its bad,the PDC
no country stated, no engine stated,? why?
the 2005 (answering for USA)
PDC hard short all fuses, all breakers all relay out
means what?
well power distribution2 below shows all that, every wire there.
ASD relay pulled? you never said relays, they can (weld closed inside contacts can)) and is unfused, this relay. fact
i read the 22 pages for you there,
its just fuses and relays, no magic until 2007 (TIPM electronics)
this car is easy fix,. due to 2005 year.

looking now , TJ unlimited it is.
see the manual yet, see how this all works 2003 to 2006 year.
chapter 8w shows wiring, and modules the rules.

8w, pdc 2, chapter see that here, its there, clear as day.'



http://www.morris4x4center.com/knowledge-base/index.htm?utm_source=cj#service

2005 Jeep... | Answered on Mar 30, 2017


to check

maf or 02 sensors
plugs ,coil, timing
fuel delivery to injectors

2005 Jeep... | Answered on Mar 08, 2017


huh?

did you read manual yet.
open glove box, read pages in oper, guide on top yet>

2005 Jeep... | Answered on Jan 03, 2017


I have an 05 6 cylinder automatic TJ. The other morning I was getting trouble codes U0101 and P1603. For a few seconds the Jeep was shaking and for the entire 30min ride it wouldn't shift into the last gear, it would just continue to rev. The next day I drove it and it was fine. I also noticed a slight high pitch whine noise coming from the engine at low speeds. Any suggestions? Thanks!

2005 Jeep... | Answered on Dec 03, 2015


check adjustment on shifter arms under on transfercase

2005 Jeep... | Answered on Aug 07, 2015


What part?

2005 Jeep... | Answered on Jun 26, 2015


Ask parts store to run the codes (usually for free).

2005 Jeep... | Answered on May 04, 2015


disconnect battery for ten min

2005 Jeep... | Answered on Apr 03, 2015


pull out spark plugs and see if they all look the same,could be dirty fuel injectors or a blocked fuel filter

2005 Jeep... | Answered on Apr 03, 2015


Sounds like the synchro mesh has worn out

2005 Jeep... | Answered on Apr 03, 2015


so its just the light bothering you, (i ignore mine) I can tell car is in 4wd or not, dont need no stinkn light, so....
is it in 4wd or not? we cant guess that. only you..
the light is hard wired to the transfer case switch
if the switch closes, you are in 4wd, or the switch is bad. end story on silly light. and fuse 10 is the power for that light.
on this car , there is no computer running this light,

im driving on what.? dirt, ice, dry pavement what?

my guess, wild. is car is in 4wd. and you are not on ice or dirt and its stuck, Part time 4wd is for dirt or ice only and will stick.

drive to dirt, or jack up 1 wheel
and shift in to 2H.
fixed now?
light out?

answering for PT 4wd . not
came new with NV231 or 241 and both are part time 4wd, now AWD.

ever read this.


http://www.rubicon-trail.com/4WD101/driveline-bind.html


dont do that, posted 100s of time here.

2005 Jeep... | Answered on Mar 17, 2015


Did you replace the O2 sensor after the catalytic converter? This code is set by the rear O2 sensor. It usually indicates early failure or restricted catalytic converter. May want to have an exhaust back pressure test performed.

2005 Jeep... | Answered on Mar 03, 2015


Clutch switch keeps it from cranking.
You can bypass the cluctch switch. Make double sure transmission is in neutral. On many jeeps, under the hood is fuse/relay box. One of the relays is the starter motor. Pull the relay. With a pair of pliers, take a paper clip and short the pins that go to starter. They wire can get hot. If the starter cranks, you might be right (see ignition switch and any interlocks - like clutch switch), if the starter doesn't crank, get a new starter.

2005 Jeep... | Answered on Feb 16, 2015


2095 ( a jeep factory code that is , jeep only)
reset. like all cars , you can reset any code, with any scan tool
but if the failure is real and present it will NOT.
that is its purpose to report real failures.
is this the 3.8Liter v6 , like mine is?
DOWNSTREAM FUEL TRIM SYSTEM 1 LEAN
down means not the front sensor.
engine >>>>Up >>>>CAT >>>> down?>>>>> tail pipe end.
this is an air leak (crack) behind the cat converter
or the sensor is bad, (down stream.)
or wires fell off, (common) LOOK FIRST.see damage there?

2005 Jeep... | Answered on Feb 16, 2015

Not finding what you are looking for?
2005 Jeep Wrangler Logo

341 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

83810 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Wrangler Jeep

  • Wrangler Jeep

Most Popular Question

gear slip when putting into first third

  • Cars & Trucks
Loading...