20 Most Recent 2010 Chevrolet Equinox Questions & Answers


Need to try some wd40 spray it in the hole where the lock piece is and try to move it may take a little bit of time if not you will need to replace the lock assembly

2010 Chevrolet... | Answered on Mar 31, 2019


There are two different ways to relearn your Tire Pressure Monitoring System (TPMS). One is with a TPMS scan tool (this is the preferred method) and the other is the manual method (pain in the "you-know what", but requires no special tools or equipment).

To use the manual method, set the parking brake. Enter into TPMS RELEARN using the Driver Information Center (DIC) controls. (SEE Owner's Manual)

When you have successfully entered TPMS RELEARN, the horn will chirp and the left front turn signal will illuminate. Increase or decrease the tire inflation pressure on the left front tire for 8 to 10 seconds. The horn will "chirp", indicating that the left front tire pressure sensor has been relearned and the turn signal at the right front will illuminate. Repeat the process for the right front tire. The horn will chirp and the right rear turn signal will illuminate indicating that the right front tire has been relearned and now you must now repeat the process at the right rear tire. Then you will have to repeat this a fourth time at the left rear. When the left rear tire has been relearned, the horn will sound a "double chirp" indicating that the relearn process has successfully completed.
At this time, turn the ignition switch to the OFF position and adjust all of the tire pressures to the specification printed on the tire certification label inside the drivers door/door pillar area.

2010 Chevrolet... | Answered on Dec 02, 2018


Yes there's a release button on the key fob.

2010 Chevrolet... | Answered on Sep 23, 2018


It's all tied together in the computer system . When you start to loose control the computer takes over reducing engine power , applying brakes etc... to bring vehicle back into control . The throttle body on your vehicle is computer controlled . electronic throttle control . the gas pedal has sensors , the throttle body has sensors an a electric motor . The lights came on because the computer disabled these systems .

2010 Chevrolet... | Answered on Feb 16, 2018


It could be a parking brake issue but it could also be a failed wheel bearing. If you get that wheel off the ground, does it flop around? If so, you need at least a bearing. It may have damaged the knuckle as well. It should have made a distinct roaring or humming sound as it was failing.

2010 Chevrolet... | Answered on Mar 07, 2017


If you have a faulty camshaft sensor, your engine won't run.

2010 Chevrolet... | Answered on Feb 14, 2017


Have to remove black cover front lower right hand side under that cover

2010 Chevrolet... | Answered on Feb 14, 2017


The emissions are either running rich or lean or the NOX is high. The emissions have to be ckd & the computer scanned for problems. You can drive it but get it ckd out as soon as u can.It can be as simple as a vacuum leak

2010 Chevrolet... | Answered on Feb 10, 2017


This make, year and model has no inline fuel filter, the only fuel filtering is done at the inlet to the electric fuel pump inside the fuel tank, it never needs to be serviced unless the fuel pump is replaced.

2010 Chevrolet... | Answered on Dec 30, 2016


DTC P0017: Crankshaft Position (CKP) - Exhaust Camshaft Position (CMP) Correlation Bank 1
Which engine does yours have 3.4 or 2.8 , 3.0 , 3.2 , or 3.6 L Chevy Colorado P0017 Case Study Part 1

2010 Chevrolet... | Answered on Dec 16, 2016


You will need to have the fault codes read from the engine control computer and then post them on this site.

2010 Chevrolet... | Answered on Nov 10, 2016


Diesels do knock on start, but that is not the only knock that there is, I would need to hear the noise it may be a rod bearing

2010 Chevrolet... | Answered on Sep 30, 2016


Solenoid, do you mean the park lock solenoid?

2010 Chevrolet... | Answered on Sep 21, 2016


The transmission has failed, time for a rebuild.

2010 Chevrolet... | Answered on Sep 20, 2016


on the front of the engine block its round with the securing bolt going through it and it will have a black lead coming from it

2010 Chevrolet... | Answered on Jun 19, 2016


u should try resetting the body computer. or unhook batt cables for a few minutes while both terminals unhooked. touch rhem together for few minutes also. then reconnect an see wat you have. u probably gonna need a decent scanner to access memory resets and component tests to properly reset the bcm body control module. good luck hope this helps

2010 Chevrolet... | Answered on Apr 04, 2016

Not finding what you are looking for?
2010 Chevrolet Equinox Logo

199 questions posted

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Equinox Chevrolet

  • Equinox Chevrolet

Most Popular Question

2010 chevy equinox check engine light

  • Cars & Trucks
Loading...